Hovedemner

Komité: CEN/TC 10 (Lifts, escalators and moving walks)
Opprinnelse:
Sluttdato: 30. jul 2020
Vis merVis mindre
 
This document specifies the minimum requirements for the safe and independent access and use of lifts by persons, including persons with disabilities. It covers the needs of persons with disabilities according to Annex A. NOTE For guidance on solutions for increased accessibility and usability, see Annex D.
Komité: CEN/TC 151 (Construction equipment and building material machines - Safety)
Opprinnelse:
Sluttdato: 30. jul 2020
Vis merVis mindre
 
1.1 This document includes safety requirements for the design and installation of equipment that is intended for storage, handling and transportation of flat glass inside the factory. It also applies to equipment within the scope of EU Directives as well as to equipment that is covered by non harmonized documents. Annex E gives an overview of the differentiation. 1.2 This document specifies safety requirements for the following equipment: - equipment for storage provided with elements that are propelled by a drive system other than directly applied human or animal power (engine power) in order to store or retrieve glass in or from storage shelves or frames (see 3.2.2); - equipment for picking up single glass plates, firmly attached glass plates or glass packs for transportation between different locations where the retention force or lifting force is generated by engine power (see 3.3.2, 3.3.3); - equipment for transportation by special vehicles that are propelled by engine power. 1.3 This document specifies additional requirements for the following equipment that is not covered by EU Directives: - stationary, movable and mobile storage equipment (see 3.2.1, 3.2.3, 3.2.4, for requirements see Annex A); - storage equipment that is provided with manually propelled shelves or frames (see 3.2.2, for requirements see Annex B); - equipment for transportation by special vehicles that are not self propelled (see 3.4.3, for requirements see Annex C). NOTE Additional requirements covering specific hazards that are resulting from the use outside the factory are dealt with in EN 13035 2. 1.4 This document only deals with equipment which is in direct contact with the glass, with the exception of wooden packaging. Tractors, cranes, hoists and forklift trucks as well as elements of self propelled vehicles, which are not in contact with the glass (see 3.4.1), are out of the scope. This document does not apply to equipment for picking up single plates, such as manual vacuum lifting devices, lifting straps or other manual devices. This document does not cover automatic loading or unloading of storage and transportation equipment. This is covered in EN 13035-5. 1.5 This document deals with all significant hazards, hazardous situations and hazardous events, which are relevant to equipment for storage, handling and transportation of flat glass, when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Annex D). This document specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards during commissioning, operation and maintenance. Noise hazards have not been considered significant for any type of equipment within the scope of this document. 1.6 This document is not applicable to equipment for storage, handling and transportation of flat glass inside the factory, which is manufactured before the date of publication of this document by CEN.
Komité: CEN/TC 151 (Construction equipment and building material machines - Safety)
Opprinnelse:
Sluttdato: 30. jul 2020
Vis merVis mindre
 
1.1 This document includes safety requirements for the design and installation of equipment that is intended for storage, handling and transportation of flat glass outside the factory. It applies to machinery within in the scope of EU Directives as well as to equipment that is covered by non harmonized documents. 1.2 This document specifies safety requirements for the following equipment for storage (see 3.2.1), handling (see 3.2.2) and transportation (see 3.2.3) of flat glass outside the factory (see 3.1.1): - vehicle mounted frails with motorized adjustment of the angle of lean for loading and unloading, which are used for road transport; - inloader vehicles for road transport outside the factory, where loading and unloading is only made on virtually horizontal and sufficiently stable grounds that are free of significant irregularities; - specific self propelled equipment for securing the glass (inloader load-securing systems); - equipment for picking up single glass plates, firmly attached glass plates or glass packs for transportation between different locations where the retention force or lifting force is generated by engine power. 1.3 This document specifies additional requirements for the following equipment that is not covered by EU Directives: - vehicle mounted frails without an adjustable angle of lean for loading and unloading, which are used for road transport; - movable storage equipment designed to transport the glass outside the factory (e.g. inloader stillages, see Figure C.6); - glass securing devices or systems for transport stillages (e.g. spring tensioning rods, stanchions). NOTE Specific hazards due to the use inside the factory are dealt with in EN 13035-1. 1.4 This document deals with road transport as wells as rail transport. 1.5 This document only deals with equipment which is in direct contact with the glass. This document does not apply to manual handling equipment such as carrying straps and manual vacuum lifting devices and to all packaging for glass which always opened and closed in the factory (see EN 13035-1). Tractors, cranes, hoists and forklift trucks as well as elements of self propelled vehicles, which are not in contact with the glass, are out of the scope. This document does not apply to the transport of glazed windows/frames, neither does it apply to equipment for different transportation than on road or on rail, e.g. by ships. 1.6 This document deals with all significant hazards, hazardous situations and hazardous events, which are relevant to equipment for storage, handling and transportation of flat glass, when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Annex B). This document specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards during commissioning, operation and maintenance. Noise hazards have not been considered significant for any type of equipment within the scope of this document. 1.7 This document does not apply to equipment for storage, handling and transportation of flat glass outside the factory, which is manufactured before the date of publication of this document as EN.
Komité: CEN/TC 164 (Water supply)
Opprinnelse:
Sluttdato: 30. jul 2020
Vis merVis mindre
 
This document is applicable to aluminium based coagulants (aluminium sulfate, aluminium chloride (monomeric), aluminium chloride hydroxide (monomeric), aluminium chloride hydroxide sulfate (monomeric), sodium aluminate and polyaluminium chloride hydroxide and polyaluminium chloride hydroxide sulfate) used directly or for the production of formulations for treatment of water for swimming pools. It describes the characteristics of aluminium based coagulants and specifies the requirements and the corresponding test methods for aluminium based coagulants. It gives information on their use in swimming pool water treatment. It also determines the rules relating to safe handling and use (see Annex B).
Komité: CEN/TC 164 (Water supply)
Opprinnelse:
Sluttdato: 30. jul 2020
Vis merVis mindre
 
This document is applicable to ammonium sulfate used for treatment of water intended for human consumption. It describes the characteristics and specifies the requirements of ammonium sulfate and refers to the corresponding analytical methods. It gives information on its use in water treatment.
Komité: CEN/TC 164 (Water supply)
Opprinnelse:
Sluttdato: 30. jul 2020
Vis merVis mindre
 
This document is applicable to calcium hypochlorite used directly, or for the production of formulations, for treatment of water for swimming pools. It describes the characteristics of calcium hypochlorite and specifies the requirements and the corresponding test methods for calcium hypochlorite. It gives information on its use in swimming pool water treatment. It also determines the rules relating to safe handling and use of calcium hypochlorite (see Annex B).
Komité: CEN/TC 164 (Water supply)
Opprinnelse:
Sluttdato: 30. jul 2020
Vis merVis mindre
 
This European Standard is applicable to sodium chlorate used for treatment of water intended for human consumption. It describes the characteristics of sodium chlorate and specifies the requirements and the corresponding test methods for sodium chlorate. It gives information on its use in water treatment. It also determines the rules relating to safe handling and use of sodium chlorate (see Annex B) and gives the environmental, health and safety precautions within chemical laboratory (see Annex C).
Komité: CEN/TC 164 (Water supply)
Opprinnelse:
Sluttdato: 30. jul 2020
Vis merVis mindre
 
This document is applicable to sodium hexafluorosilicate used for treatment of water intended for human consumption. It describes the characteristics of sodium hexafluorosilicate and specifies the requirements and the corresponding test methods for sodium hexafluorosilicate. It gives information on its use in water treatment. It also determines the rules relating to safe handling and use of sodium hexafluorosilicate (see Annex B).
Komité: CEN/TC 164 (Water supply)
Opprinnelse:
Sluttdato: 30. jul 2020
Vis merVis mindre
 
This document is applicable to liquefied ammonia used for treatment of water intended for human consumption. It describes the characteristics and specifies the requirements of liquefied ammonia and refers to the corresponding analytical methods. It gives information for its use in water treatment. It also determines the rules relating to the safe handling and use of liquefied ammonia (see Annex B).
Komité: CEN/TC 164 (Water supply)
Opprinnelse:
Sluttdato: 30. jul 2020
Vis merVis mindre
 
This document is applicable to sodium used for treatment of water intended for human consumption. It describes the characteristics and specifies the requirements of sodium sulfite and refers to the corresponding analytical methods. It gives information for its use in water treatment.
Komité: CEN/TC 164 (Water supply)
Opprinnelse:
Sluttdato: 30. jul 2020
Vis merVis mindre
 
This document is applicable to sodium hydroxide used for treatment of water intended for human consumption. It describes the characteristics and specifies the requirements and the corresponding test methods for sodium hydroxide. It gives information on its use in water treatment.
Komité: CEN/TC 164 (Water supply)
Opprinnelse:
Sluttdato: 30. jul 2020
Vis merVis mindre
 
This document is applicable to filter media (virgin granular activated carbon, silica sand and silica gravel, pumice, pyrolyized coal material, anthracite and calcium carbonate) used for treatment of swimming pool water. It describes the characteristics of filter media and specifies the requirements and the corresponding test methods for filter media. It gives information on their use in swimming pool water treatment. This document does not concern powdered diatomaceous earth, perilite, zeolite and similar materials used with filter cartridges.
Komité: CEN/TC 164 (Water supply)
Opprinnelse:
Sluttdato: 30. jul 2020
Vis merVis mindre
 
This document is applicable to powdered activated carbon used for treatment of swimming pool water. It describes the characteristics of powdered activated carbon and specifies the requirements and the corresponding test methods for powdered activated carbon. It gives information on its use in swimming pool water treatment.
Komité: CEN/TC 164 (Water supply)
Opprinnelse:
Sluttdato: 30. jul 2020
Vis merVis mindre
 
This document is applicable to sodium thiosulfate used for treatment of water intended for human consumption. It describes the characteristics and specifies the requirements of sodium thiosulfate and refers to the corresponding analytical methods. It gives information for its use in water treatment.
Komité: CEN/TC 164 (Water supply)
Opprinnelse:
Sluttdato: 30. jul 2020
Vis merVis mindre
 
This document is applicable to iron based coagulants (iron (III) chloride, iron (III) chloride sulfate and iron (III) sulfate liquid) used directly or for the production of formulations for treatment of water for swimming pools. It describes the characteristics of iron based coagulants and specifies the requirements and the corresponding test methods for iron based coagulants. It gives information on their use in swimming pool water treatment. General information on iron based coagulants is given in Annex A. It also determines the rules relating to safe handling and use (see Annex B).
Komité: CEN/TC 110 (Heat exchangers)
Opprinnelse:
Sluttdato: 30. jul 2020
Vis merVis mindre
 
This document specifies methods to be used for testing of air-to-air heat recovery components (HRC). The main purpose of the HRC is to exchange heat between exhaust air and supply air in order to save energy, which results in — preheat or heat, and/or — precool or cool supply air in ventilation systems or air conditioning systems. Optionally HRC can exchange air humidity between exhaust and supply air. The HRC contains the heat exchangers and all necessary features and auxiliary devices for the exchange of sensible heat and (if available) air humidity between exhaust air and supply air. The HRC will be installed in casings or ducts. If fans are part of the test unit, the effect of the fan power on the measured values will be corrected. This document specifies procedures and input criteria required for tests to determine the performance of a HRC at one or several test conditions, each of them with continuous and stationary air flows, air temperatures and humidities at both inlet sides. Three different test types are covered: — Test type A, Laboratory testing of HRC installed in test casings (A1) or a HRC sections (A2); — Test type B, Laboratory testing of HRC installed in non-residential ventilation units in design configuration; — Test type C, On-site (field) testing of HRC in non-residential ventilation units (C1) or a HRC sections (C2) in operation configuration. This document is applicable to recuperators, regenerators, and HRC with intermediary heat transfer medium. This document prescribes test methods for determining: 1) the temperature and humidity efficiency, 2) the pressure drop of exhaust air and supply air sides, 3) possible internal leakages; exhaust air transfer ratio (EATR) and outdoor air correction factor (OACF), 4) external leakages and 5) auxiliary energy used for the operation of the HRC. HRC using heat pumps are not covered by this document.
Komité: CEN/TC 275 (Food analysis - Horizontal methods)
Opprinnelse:
Sluttdato: 30. jul 2020
Vis merVis mindre
 
This European Standard specifies a method for the determination of five Alternaria toxins in wheat, tomato juice and sunflower seed samples by liquid chromatography tandem mass spectrometry (LC-MS/MS). The method includes the analysis of Altenuene (ALT), Alternariol (AOH), Alternariol monomethyl ether (AME) in the range of 1 μg/kg to 100 μg/kg, and Tentoxin (TEN) in the range of 5 μg/kg to 500 μg/kg, and Tenuazonic acid (TEA) in the range of 10 μg/kg to 1000 μg/kg.
Komité: CEN/TC 240 (Thermal spraying and thermally sprayed coatings)
Opprinnelse:
Sluttdato: 30. jul 2020
Vis merVis mindre
 
This document specifies safety requirements of machines and equipment for thermal spraying, in this case of gas control units. This document should be used in conjunction with the Part 1 which deals with general aspects when designing, manufacturing, and/or putting in service of machines or equipment. Generally the requirements of EU-Directive 2014/34/EU are valid for the use of this document.
Komité: CEN/TC 290 (Dimensional and geometrical product specification and verification)
Opprinnelse:
Sluttdato: 30. jul 2020
Vis merVis mindre
 
This part of ISO 10360 specifies the acceptance tests for verifying the performance of an optical CMS (coordinate measuring system) when measuring lengths as stated by the manufacturer. It also specifies the reverification tests that enable the user to periodically reverify the performance of the optical 3D CMS. An optical 3D CMS that this standard intends to specify is a contactless area measuring sensor delivering 3D surface data in several individual single views by an optical measuring principle and transforming it into a common coordinate system. Typical optical measuring principles are pattern projection, fringe projection, and project-and-sweep a scanned line, or similar, delivering single views without assistance of external information related to position and orientation between CMS and objects to be scanned. Typical registration principle is based on a best fitting of commonly captured position information across at least two different single views either or both by using reference targets or surface features of objects to be scanned.
Komité: CEN/TC 237 (Gas meters)
Opprinnelse:
Sluttdato: 30. jul 2020
Vis merVis mindre
 
This document specifies requirements and tests for the construction, performance and safety of class 1,5 Capillary Thermal-Mass Flow sensor gas meters (hereinafter referred to as meter(s)). This applies to meters having co-axial single pipe, or two pipe connections, that are used to measure volumes of fuel gases of the 2nd and/or 3rd family, as given in EN 437:2018. In general, the term "thermal mass flow meters" applies to a flow-measuring device using heat transfer to measure and indicate gas flowrate, as defined in ISO 14511. NOTE 1 Although the word "mass" is present in the definition of the measurement principle, gas meters covered by this document provide measurement of gas at base conditions of temperature and pressure. These meters have a maximum working pressures not exceeding 0,5 bar and a maximum flowrate not exceeding 160 m3⋅h−1 over a minimum ambient temperature range of −10 °C to +40 °C and a gas temperature range as specified by the manufacturer with a minimum range of 40 K. This document applies to meters indicating volume at base conditions, which are installed in locations with vibration and shocks of low significance. It applies to meters in: - closed locations (indoor or outdoor with protection, as specified by the manufacturer) with condensing humidity or with non-condensing humidity; or, if specified by the manufacturer: - open locations (outdoor without any covering) both with condensing humidity or with non-condensing humidity; and in locations with electromagnetic disturbances likely to be found in residential, commercial and light industrial use. For meters which indicate unconverted volume reference can be made to Annex C. Unless otherwise stated, all pressures given in this document are gauge pressures. Requirements for electronic indexes, valves and additional requirements for batteries incorporated in the meter and any other additional functionalities are given in EN 16314:2013. Unless otherwise stated in a particular test, the tests are carried out on meters that include additional functionality devices intended by the manufacturer. Clauses 1 to 13 are for design and type testing only.