Lim

Emner: Lim
Komité: CEN/TC 193 (Adhesives)
Opprinnelse:
Sluttdato: 10. jan 2019
Vis merVis mindre
 
This document specifies test methods for the evaluation of the expansion properties for moisture curing, self-curing or water drying foams dispensed from single pressurized containers. This document does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use. The following test methods are described: - Dimensional Stability: This test method describes how to determine the dimensional stability (shrinkage or expansion) of cured foam under typical and extreme conditions. - Curing Pressure: This method describes how to determine the generation of pressure during the curing process of an OCF. - Post Expansion: This method describes how to measure the expansion of a freshly dispensed liquid foam (froth) during the curing phase.
Emner: Lim
Komité: CEN/TC 193 (Adhesives)
Opprinnelse:
Sluttdato: 10. jan 2019
Vis merVis mindre
 
This document specifies test methods for the evaluation of the yield characteristics properties for moisture curing, self-curing or water drying foams dispensed from single pressurized containers. This document does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use. The following test methods are described: - determination of the apparent density of an OCF extruded in a joint and calculation of the theoretical foam volume (yield) in running meters of the whole can; - determination of the total foam volume for the whole OCF container; - determination of the real volume of cured foam, respecting eventual cavities inside the foam structure; - determination of the density of a cured OCF for identification purposes only.
Emner: Lim
Komité: CEN/TC 193 (Adhesives)
Opprinnelse:
Sluttdato: 10. jan 2019
Vis merVis mindre
 
This document specifies test methods for the evaluation of the application properties for moisture curing, self-curing or water drying foams dispensed from single pressurized containers used as an insulating air sealant and adhesive for both building and non-building applications. This document does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use. - The following test methods are described: Cutting Time: This test method describes how to determine the hardening time of a freshly foamed OCF (froth) until it can be cut. - Tack Free Time: This test method describes how to determine the tack free time of a freshly foamed OCF. - Sagging Behaviour: This test method describes how to evaluate the sagging behaviour and determine the biggest joint possible before a liquid OCF (froth) slips off.
Emner: Lim
Komité: CEN/TC 193 (Adhesives)
Opprinnelse:
Sluttdato: 10. jan 2019
Vis merVis mindre
 
This document specifies test methods for the determination of the suitability of two component epoxy and two component polyurethane adhesives for glued-in steel rods in glued laminated timber (GLT) and glued solid timber (GST) according to EN 14080, cross laminated timber (CLT) according to EN 16351 and laminated veneer lumber (LVL) according to EN 14374. It specifies performance requirements and the determination of characteristic bond strength values for such adhesives for the prefabrication under factory or factory-like conditions of load-bearing timber-steel rod joints only. This document does not cover the performance of adhesives for on-site gluing (except for factory-like conditions). Several provisions of this document can apply to repair and upgrading of existing timber structures including (cracked/fissured) solid wood beams. For adhesives for on-site repair or applications with solid timber additional provisions need to be taken into account. Such provisions are not part of this document. This document also covers glued–in rods in surface treated wood. It does not cover glued-in rods in modified and stabilized wood with considerably reduced swelling and shrinkage properties, e.g. such as acetylated wood, heat treated wood, polymer impregnated wood and preservative treated wood. The joints are intended for load-bearing timber structures subjected to temperatures up to 60 °C over a longer time in service classes 1 and 2 which are loaded predominantly static or quasi static according to EN 1990 and EN 1991-1-1. A design procedure for glued-in rods for timber structures is given in an informative Annex A.
Emner: Lim
Komité: CEN/TC 193 (Adhesives)
Opprinnelse:
Sluttdato: 10. jan 2019
Vis merVis mindre
 
This document specifies test methods for the evaluation of the insulation properties for moisture curing, self-curing or water drying foams dispensed from single pressurized containers used as an insulating air sealant and adhesive for both building and non-building applications. This document does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use. The following test method is described: - Thermal conductivity: This method describes how to determine the long term thermal conductivity of a cured OCF foam, dispensed from a pressurized can, with a sample subjected to accelerated ageing procedure.
Emner: Lim
Komité: CEN/TC 193 (Adhesives)
Opprinnelse:
Sluttdato: 10. jan 2019
Vis merVis mindre
 
This document specifies a method for testing the strength of wood adhesives at 80 °C. NOTE The procedure described is based on a test developed in Germany known originally as the WATT '91 test. It uses the test piece described in EN 205.