Jern- og stålprodukter

Komité: ISO/TC 17/SC 17 (Steel wire rod and wire products)
Opprinnelse: ISO
Sluttdato: 3. mar 2023
Vis merVis mindre
 
Komité: ISO/TC 17/SC 11 (Steel castings)
Opprinnelse: ISO
Sluttdato: 24. mar 2023
Vis merVis mindre
 

ISO 11973:2015 specifies chemical composition and mechanical properties of cast steels and alloys for heat-resistant service.

Komité: ISO/TC 17/SC 11 (Steel castings)
Opprinnelse: ISO
Sluttdato: 24. mar 2023
Vis merVis mindre
 

ISO 11972:2015 specifies cast steels for general corrosion-resistant applications. The grades covered by this International Standard represent types of alloy steel castings suitable for broad ranges of application which are intended for a wide variety of corrosion applications.


NOTE Annex A gives information on ISO grade designation and available UNS numbers which are similar to the ISO grade designation.

Komité: ISO/TC 17/SC 11 (Steel castings)
Opprinnelse: ISO
Sluttdato: 27. mar 2023
Vis merVis mindre
 

ISO 9477:2015 specifies requirements for four grades of heat treated cast carbon and alloy steels for general engineering and structural purposes.


In cases where castings are produced by welding component parts together, this International Standard does not cover the welding process or the properties of the weldment.


The four steel grades are intended for service at ambient temperature. However, properties at other temperatures can be agreed on through the use of supplementary requirements in ISO 4990.

Komité: ISO/TC 17/SC 11 (Steel castings)
Opprinnelse: ISO
Sluttdato: 29. mar 2023
Vis merVis mindre
 

ISO 4993:2015 specifies the general requirements for the radiography of steel and iron castings by means of X-rays or gamma-rays, in accordance with procedures given in ISO 5579 and ISO 19232.

Komité: CEN/TC 459/SC 10 (Steel tubes, and iron and steel fittings)
Opprinnelse: SN
Sluttdato: 30. mar 2023
Vis merVis mindre
 
This document specifies the technical delivery conditions for qualities TR1 and TR2 of electric welded and submerged arc welded tubes of circular cross section, with specified room temperature properties, made from non-alloy quality steel. NOTE 1 Quality TR2 is intended to support the essential requirements of EU Directive 2014/68/EU in respect of pressure equipment with specified room temperature properties (see Table 5). NOTE 2 Once this standard is published in the Official Journal of the European Union (OJEU), presumption of conformity to the Essential Safety Requirements (ESR) of Directive 2014/68/EU is limited to the technical data for the materials in this standard and does not presume adequacy of the material for a specific item of pressure equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of a specific item of equipment to verify that the ESRs of the Pressure Equipment Directive are satisfied, needs to be done by the designer or manufacturer of the pressure equipment, taking also into account any subsequent processing procedures which may affect properties of the base materials.
Komité: CEN/TC 459/SC 4 (Concrete reinforcing and prestressing steels)
Opprinnelse: SN
Sluttdato: 30. mar 2023
Vis merVis mindre
 
1.1 This document specifies general requirements and definitions for the essential characteristics of weldable reinforcing steel used for the reinforcement of concrete structures, delivered as finished products in the form of: - bars (including those produced by the reinforcing steel manufacturer from coil); - coils; - sheets of factory-made machine-welded fabric; - lattice girders. 1.2 Steels according to this document have a ribbed, indented or smooth surface. NOTE 1 The protrusions between indentations of indented reinforcing steel have the same function as transverse ribs of ribbed reinforcing steel. There is no definition which specifies the difference between ribbed and indented surface geometry. Therefore, in this document, the same bond parameters are used for ribbed and indented steel. 1.3 This document does not apply to: - non-weldable reinforcing steel; - galvanized reinforcing steel; - epoxy-coated reinforcing steel; - corrosion resistant reinforcing steel; - prestressing steels; - indented strip; - further processing by a processor, e.g. de-coiling/straightening, cutting or cutting and bending. NOTE 2 Further processing could influence some essential characteristics of the product.
Komité: CEN/TC 459/SC 8 (Steel sheet and strip for electrical applications)
Opprinnelse: SN
Sluttdato: 30. mar 2023
Vis merVis mindre
 
This European Standard is intended to define the test methods used for the determination of the following geometrical characteristics of electrical steel sheet and strip: — edge wave (wave factor); — residual curvature; — edge camber; — deviation from the shearing line due to internal stresses; — burr height of cut edges. This European Standard applies to electrical steel sheet and strip intended for the construction of magnetic circuits and corresponding to Clauses B2, C21 and C22 of IEC 60404-1:2000.